What is it , can I spray it
I have a monojet pal?You will be able to spray this with your Ritmo mate. It is mineral top coat for EWI systems mate. Comes in various aggregate sizes: 1.5mm - 2mm and 3mm
I have a monojet pal?
Prob a different gun to ?Sorry mate, my mistake! To my knowledge you will be able to spray it with your mono jet. I will have to check what R/S you need to use as I can't remember off the top of my head. Will drop you a message tomorrow mate
Prob a different gun to ?
Hi Mate,
Have just doubled checked. A D4-3 R/S would be the best to use. I asked asked one of our customer who used to have that machine. He sprayed with a Texture gun and said that gave the best results.
The Germans use a D4-3 cos it mixes it better. if you look on you tube there are vids somwhere. Laying noblo on too thick is not the same as laying too much pre mixed bucket coat on because it spreads about far more evenly and there is much less drag when trowelling it to finish.
And the monojet compressor or a bigger capacity one ?
its the same. just use a 8mm cap and you will be fineSo I need a texture gun and a different r&s then I can go straight into the hopper with the dry powder and the monojet will mix and pump? I saw something similar in Germany guys where spraying a bagged texture with a G4 then flattened out with a big spat and troweled finished. Would this be the same ?
thanks ian. That looks very fast. I shud have plenty man power with a team of 3 then inc myself. The contractor has quite abit of this wrk for me so knowing I can spray it is a big plus. Cheers
These boys look the bolloxx. that may even be a 14 or 16 mm cap. he's getting it on just right for his pal
thanks ian. That looks very fast. I shud have plenty man power with a team of 3 then inc myself. The contractor has quite abit of this wrk for me so knowing I can spray it is a big plus. Cheers
These boys look the bolloxx. that may even be a 14 or 16 mm cap. he's getting it on just right for his pal
Cheers bud. Be at least a week after the base maybe 2 b4 it gets topped. Mad busy atm. So just when I can get to itNice one lee.Keep an eye on the weather mate as it will catch you out Bigtime.
I might come on for a day Lee just for the bash. Id like to have a crack at spraying noblo with 3phases.......giddy
Will do johnJust let me know when the noblo is gonna go on and if I can get away from job I will come down
Just let me know when the noblo is gonna go on and if I can get away from job I will come down
was thinking so. One on spat and one finishing , burning shoulder for gene on the finishing. Yeah sure John. It's over on the wirel thoughSame here.
Remember that vid. Incredibly fast but that wall of yours will be easy with a mono and plenty of hands. A morning?
The monojet compressor is a k2. its 250 ltrs a minute and is absolutely fine for applying Noblo. A bigger compressor will offer no benefit here
The D4-3 is a 10/12 ltr pump so its gonna pump way too fast to leave as a finished sprayed texture. The time saving is that the material is mixed, applied and trowel finished immediately. Its far easier to spread than silicone or acrylics and you dont get hardly any residue building up on your trowel
Nice one lee.Keep an eye on the weather mate as it will catch you out Bigtime.
So I need a texture gun and a different r&s then I can go straight into the hopper with the dry powder and the monojet will mix and pump? I saw something similar in Germany guys where spraying a bagged texture with a G4 then flattened out with a big spat and troweled finished. Would this be the same ?
was thinking so. One on spat and one finishing , burning shoulder for gene on the finishing. Yeah sure John. It's over on the wirel though
The comp on my minijet is different to the k2 but I assume the same spec more or less? Will it do the mineral
yes the air is suited to the output. it will do it easily. remember its only gotta get on the wall, you're man trowelling does most the graft