Recent content by gooty

Quality NOT quantity!!! I'd rather plaster 7 perfect walls than 8000 shite ones pmsl. There are a few helpful intelligent guys on here (my thanks to those), but pretty much every post gets pathetic bitchy replies from miserable morons like the ones above. Anyway, I think it's time to leave...

Thanks for the sensible reply. I have plastered 8 walls in this property. All of the walls were taken back to bare brick, repointed, rendered #1 (4S:1C) #2 (5S:1C:1/2L), Bluegrit suction controlled and plastered in multifinish. All 7 without using Extratime are perfect and as smooth/flat as...

You can't be arsed to explain, but you can be arsed to post your inane reply PMSL. Anyway, I assumed it was a good product until this happened. After a bit of research, I found out that I'm not the only person that this has happened to. It's quite common. I've also found out that it's 'made' by...

I'm gutted. I rendered a large area in S&C and then used bluegrit. Thought I'd try Extratime in the multifinish due to the size of the plastering. The product was in date (expires 2023). Purchased from Travis Perkins. 1 Packet added to 12L of water. Thoroughly mixed before adding to 25kg bag of...

I've got a small window that has a wooden lintel. I know most of you guys will say to fix plasterboard to it then skim, but how was it done with S&C render in the old days? I'm guessing it was by nailing EML onto it then rendering? if not, was a better way of getting a perfectly level finish? I...

That was a good guess. It's exactly 10ml. So you need 4 capfuls of Febmix to every 14L buckets of cement.

These companies spent a lot of time/money producing this product. They give mixing instructions for a reason. Too much plasticiser, and the strength of the mix will be compromised. Too many air bubbles are formed which substantially weakens the cement mix. I couldn't find the answer so thought...

OK, so I've filled a 13 litre bucket with cement, and it weighs 15.5Kg. That works out at 38.75ml of Febmix (at the lowest ratio of125ml:50Kg)

I know most people say to read the instructions or just throw in a cap full of febmix but I would like to know what the actual amount should be. The instructions give 2 ways of calculating it. 1) 125ml-250ml Febmix : 50Kg cement 2) 1L Febmix : 200 litres water As most people use 14L buckets...

The area is about 30m2 but I'm so slow I had trouble finishing one about 16m2 the other week. I guess I'd just like to know if the mesh way mentioned above will work without cracking along the joins or if there's another way that would be better (other than doing it in one hit)?

I have an area to internal render that's too large for me to do in one go. Could I just U nail brick reinforcing mesh vertically down the center of the wall with a wood baton screwed down the middle of it. Then render up and onto one side of the mesh, butting it up against the baton. Next day...

Thanks for the helpful replies. I only wanted a rough idea, so as to not over/under order. I just assumed you professionals would need to know the basics of this to do your job. Anyway, I asked someone as clever as you lot and he said the bag is a m3. So each '15mm slice' would be a m2. There...

I have done internal rendering, but the 'plastering' sand was full of small stones. PITA but it went on and the finished job turned out OK. BTW I cannot do the numbers (would love to see your workings out lol), but assumed most professionals here would know roughly how many m2 per jumbo bag.

interior rendering a large area about 10-15mm thick 4:1. don't wanna order too little or way too much. any ideas roughly how many m2 from a jumbo bag? thanks. BTW do you bother using plastering sand and use sharp instead?

The unistrut S&C rendering worked great in a small bathroom. The walls were all laser level and perfectly flat, but using the unistrut was heavy/bulky and a bitch to clean for reusing. However, the plastered walls looked amazing at the end and the tiles went on much easier. I was impressed when...