Search results

  1. C

    hardwall water level on ritmo

    I'm running a ritmo l on a maintenance free r/s ,we've been spraying hard wall this week at 325 water speed 10
  2. C

    Afternoon sprays yet?

    What sort of dosage do you work to rigsby with the retarder? And have you tried it with k rend?
  3. C

    Afternoon sprays yet?

    Sprayed at 3 yesterday on hp12 base coat 50sqm temps where supposed to be 12 degrees last night.got there this morning and had to hack the lot back off lol. I'm gutted really:cachetada::crying:
  4. C

    Base coat ghosting

    Yeah would of done the r7 jrend but haven't got any to hand. I'm sure someone on here has said that there r7 is just there version of sbr
  5. C

    Sas Europe Launch Fast and Easy Monocouche Render for New Builds

    If I remember rightly Clemo,there hardly anything in it for the top coat about 10-11 including vat. But the prep coat is about 16 plus vat but it has fibres in it and is also nice to spray.
  6. C

    Sas Europe Launch Fast and Easy Monocouche Render for New Builds

    Iv used there gear a few times now,but it does take a long time to go off. There prep coat is 100% waterproof so they say. I sprayed it once (top coat hbs)and the temperature was only 12 degrees ,sprayed the Wednesday and couldn't scratch it back till Friday mid day!!! But nice gear to use
  7. C

    Base coat ghosting

    I was just thinking of putting a coat of sbr over the base coat to see if this would seal it and then creat an equil suction over the whole area an hour before I spray eliminating the ghosting areas,Iv never had this problem before. By doing it an hour before I was hoping it would still give it...
  8. C

    Base coat ghosting

    Only because I'm spraying 12mm mono over the top arti
  9. C

    Base coat ghosting

    So would it be ok to put some sbr over it an hour before top coating ?
  10. C

    Afternoon sprays yet?

    Thinking of doing a afternoon spray tomorrow,starting about 2.30-3ish k-rend on top of hp12,so it should hold it back abit. Night time temps are about 13 degrees at the mo
  11. C

    Base coat ghosting

    hi guys Anybody ever had areas of block lines ghosting through there Basecoat? Iv used hp 12 and in some areas its ghosted,and I'm a little concerned it with go through to the top coat. Iv never had this happen before and the Basecoat has been on 7 days now. Blocks where dry but it's even in...
  12. C

    screeding boj jobs

    N No mate Wales
  13. C

    screeding boj jobs

    Tripods set with a tape measure,and no slump test done an any of the trucks.
  14. C

    screeding boj jobs

    I'm not going to mention the name,as much as I want to the way I look at it now is the jobs been sorted,and lesson learned. I have to take responsibility for it myself as I should of checked the guy out before I subbed him the job.
  15. C

    screeding boj jobs

    Yes Nigel I had to scabble the whole floor,then I had to hover it within an inch of its life!! Twice I hovered it to get all the dust up in between brushing it also. I had to purchase a resin from tech floor (as gyvlon gave me a spec to work to on the preparation) So this was a two pack...
  16. C

    screeding boj jobs

    I subbed a liquid screed floor out to a guy a year ago who apparently had been doing them for years (he was on this forum ) and what he left me with was worse than that. 220 Sqm all f**k*d cost me £7k to put it right. I now use a guy regularly who is spot on with the floors
  17. C

    The M-tec M200 - It's finally here!

    Ryan when is the gun for the base coats coming out? The one that was on YouTube,I'm sure it was the eze 86 or something like that spraying really nice and neatly. we did talk about it when I was up having my training a while back
  18. C

    Thin coat to 1.5

    I remember not to shut off or open up onto the wall lol
  19. C

    Thin coat to 1.5

    hey guys going to be spraying this over the weekend first time Iv used it,any hints and tips or does and donts with this gear. Using the eze 24 to spray it,and before I get murdered I am a ritmo user too Base coat has all been done (hp12) and been left for about 2 n half weeks so nice and...
  20. C

    Ritmo users

    Only takes someone to have a s**t and flush the bog,then there's trouble Like you say always best to run off a pump out of the barrel
  21. C

    Ritmo users

    I thought it had to be a minimum of 2.5 bar of water pressure to keep the machine going,I could be wrong though.
  22. C

    Bauwer render samples

    hey guys Have any of you lot used your samples yet?? I used the Bauwer light and thought it was great used it for some dubbing out that was about 50mm thick. Mixed it up and slapped it in with some mesh and the stuff didn't even move its great lol. I can see me placing a few orders with this...
  23. C

    Spraying two passes

    Cheers rob We noticed today before we started spraying that the spray cap (coned one) Was worn it still looked new but the hole had to be about 16mm lol. To the point that I made sure it was a ten and it said ten on it,must be all that hard wall we sprayed with it. Anyway chucked it away put a...
  24. C

    Spraying two passes

    :musculoso:
  25. C

    Spraying two passes

    We normally just get a mallet or chop um off with a trowel as there normally only out 5-10 on a good day. But this job is being done through a garuntee company so they come and inspect. Can you imagine if they came down and said where's the weep vents:hola: I'd get proper:bananas:
  26. C

    Spraying two passes

    I normall spray on top of a base coat so one pass and I rule it's fine,but the block work on this job was done by steve e wonder. It varies up to nearly 12mm and that's just over a 1100 window angle bead:frenetico: So we base coated but have still had to do two passes,but as they are only small...
  27. C

    Spraying two passes

    It's not going to bad lads I dropped the speed down to 8 on the machine and it's ok still a bit hit and miss for him though but better than before.
  28. C

    Spraying two passes

    Amen to that rigsby,
  29. C

    Spraying two passes

    I do keithuk but he gets his head up his ass a lot when I keep going on at him then sulks so it doesn't get any better,he always says to me with attitude "I always say if you can get someone else to spray then do it" When he gets paid £25k a year off me I expect him to be good by now. But he's...
  30. C

    Spraying two passes

    Hi all Ritmo users I'm just wondering how you other machine guys spray your two passes,ie do you spray through one or two lifts with the first pass then back up to do a second pass, or do you just spray a lift at a time . firstly spray right to the end of the lift and back to the beginning...
  31. C

    Nozzle for thin coat

    Lol and there it is :cachetada:
  32. C

    Nozzle for thin coat

    I'd imagine it would be on the lk402 compressor and gun set up ect
  33. C

    Eze 24

    It got combed gibbo lol
  34. C

    Eze 24

    Y Yes you are right Ian it does say it on the bag also:hola:
  35. C

    Eze 24

    Used an easy spat and then keyed
  36. C

    Eze 24

    I done 7 to start with on Saturday,but that was two wet for me,it looked like the building was having a stroke when it was all sliding down the wall:frio: Today just used 6 and it was spot on for me:bananahappy:
  37. C

    Eze 24

    Before you all shoot me down for having a 24,I am a Pft ritmo user and have been for the last three years:bailando: But I must say this little thing is great,I bought it about 3-4 months ago and used it for the first time Saturday to spray a bit of rend aid few teething problems but that was...
  38. C

    Ritmo water ptroblem

    Fk me 36 pallets!! Fair play
  39. C

    Bristol

    Jgreenplastering
  40. C

    Ritmo water ptroblem

    I had this problem rigsby when I was spraying hard wall,the water was just slowly dropping,it turned out to Be the main water filter under the bottom of the machine. The one were you need the G** spanner to undo it,took it out and it was blocked for sure. I have also had my tap replaced as...
  41. C

    Eze 24 training

    I'll be down tomorrow:bananas::asadito:
  42. C

    Eze 24 training

  43. C

    Eze 24 training

    I bought the eze for a thin coat job Iv got on in the next couple of months,I bought it a while back knowing I got this job for it and got it for a good price. But I'm thinking of chucking some rend aid through it next week or so you know what it's like when you got a new toy to play...
  44. C

    Eze 24 training

    bobby I didn't realise that was you from here,didn't reconise you it must of been the frost you were covered in. I will bring a heater next time lol. Have you done your texturing yet mate?
  45. C

    Eze 24 training

    I'd better say thanks to Ian jones aswell for servicing my ritmo last Friday in the freezing weather conditions at Pft wales. Also a top job and always a pleasure. P.s buy a fcking kettle.
  46. C

    Eze 24 training

    Would just like to say a big thanks to the plasterers one stop shop for my training today on an eze 24 I bought second hand a few months back on eBay. Ryan squeezed me in a short notice, and I can't wait to get the little thing to work,again thanks Ryan and Andy for you time and for what...
  47. C

    sp11 dqr wanted

    Re sprayed theclemo I bought it like this and have never used it as it was previously used for pumping concrete for piling,it comes with no render hoses or guns but 200 mtrs of screed/concrete hose so good others not so good
  48. C

    sp11 dqr wanted

    Hi Iv got a brinkmann dhl d2 I may be selling.
  49. C

    Best place and price for weber

    :sorprendido3: Rigsby:frenetico:
  50. C

    Best place and price for weber

    Hi guys Where are people finding the best deals on weber at the mo. I mainly spray k rend but have a weber job coming up and I do love spraying and ruling this when Iv been doing so much k rend,weber just feels so much better when ruling. I have been buying my k rend from amaroc in swindon great...
Top