Search results

high humidity in property.get the humidity down problem solved.

503 newton mesh dot n dab. sorted.

sbr wall...lay on one coat render mesh it up flatten it out..1mill silicon finish.done

I haven't top coated the side wall yet .

Life savours.lads could of bugged it all up at the end arrrr

If its at least 100litre it will be fine mt

Looks like ile have to get onother spread thanks for the advise fellers.much appreciated.....this stuff come in tubs 25kg in white its thick rep said add a cup or two of water.whats you opinions

Check it first with a damp meter And a moister meter see what the humidity in the house is.if its high get a dehumidifier.if the wall shows damp on the reading there your answer.

Not cheap I payed 250 for the gun about the same for the compressor. It will work on a smaller compressor. If you do a lot well worth the cash.will spray an orange peel texture real nice. Use tarmac ocr as tyrolyn dogs nuts mt.

Cheers Rossi. How much time will it give me cheers

Cheers dann you've got me worried now.this is johnstons 1.5 mill The rep says I've got plenty of time. I've not used the stuff before.is there any tips on slowing it down or splitting the erea to cover or leaving a thick bead to pick up .on .cheers mt

Marshall town sharp shooter. 150 ltr compresser.dogs bollucks

Render breached damp course at the bottom.

Hey fellers just finished renderering a house and just primed it ready for 1.5 silicon finish. Most of the ereas are small so no bother having plenty of time floating over. I have side wall 9mtsx7mts .do I have enough time to get it all on in one go. Appreciate the advice

it could be the paint thats reacted with the bead .just a thought. there word against yours mt.

Yes a builder has all ready done the work.

hy lads bit of advice. got a job in the pipeline got a semi detached house block work and quins on the corners .not thermalites by the way. he wants render sand cement lime .dilemma is the thickness will only be quarter of an inch thick total including scratch and top coat. i will turn it it...

wood float I prefer .round of the corners sand the base down smooth .good to go.

wood float I prefer .round of the corners sand the base down smooth .good to go.

maybe he was an ex mountaineer and wanted to do a 3d image of his past experiences to remind him of the good times he had in the Austrian alps.haa

yes mt .got to cover everything up its murder.

buy yourself a couple bags of 8mill plastic wall fixings from alliance and remedial dampproofing .drill a hole hammer it flat .the dogs bollox for fixing beads in any substrate

install 503 newton mesh on to walls .3x2 stud sound proof board. Not cheep though .

yes mate. one coat is usually enough its oil based .feels like plastic once dried .takes around 7 days to fully cure. good gear used it on four jobs . not cheep though £150 notes 20 ltr

cheers mt.

rendered over unpainted pebble dash .solid by the way. finished with Reno tex paint. Put on through a sharp shooter gun . reno tex paint ten times thicker than sand tex . water resistant in ten mins.very sticky stuff .

two and half bar .when the trigger is pressed. Set the adjustment nut half way..

third nozzle from the smallest hole.to be honest they will all do a fine texture, depending on how much air pressure you set it to.

ile try again pissing me self .

lmao,

sharp shooter .superb for fine texture work 20170812_071821.jpg 20170812_071821.jpg 4.3 MB Preview attachment 20170810_112950.jpg 20170810_112950.jpg 7.2 MB 4.3 MB Preview attachment 20170810_112950.jpg 20170810_112950.jpg 7.2 MB

sorry my mate .must be my fat fingers .

JUST A THOUGHT ANYBODY USED THIS PRODUCT FOR A ORANGE PEEL FINISH. ILE BE SPRAYING IT FROM A SHARPSHOOTER GUN. SURE YOU CAN USE THESE THIN COATS FOR A ORANGE PEEL FINISH.I COULD BE WRONG THOUGHTS PLEASE LADS.

what's it like mate .do you have to prime new render walls first .and what's the setting time cheers mucky

all these products so confusing ,any of you lads used kreisel 1.5mill . cheers lads

don't touch Travis p ....shxxxte

mkm plastering sand .4x1x1 sets rock hard lovely stuff

thanks for the quick replies lads . ile be doing a traditional scratch coat over solid pebble dash .ie council dwelling. then top coat level and float finish..ile be using lime in my mix . do I need to prime top coat . ive not used anything like these product before but been in the trade 17yrs...

ok lads another question . can I apply vimark on traditional sand cement and lime render .sponge finish . never used vimark .

the perfect mix for me is 4sand 1 cement 1 lime plus water proofer,perfect. when you can run your float up and down on the render without drag that's the perfect mix.

ye I was going to give it a go on my own walls before attempting a paying job lols.

another question mick. is the gun as good as they say. and what do you set it up for for orange peel as in the trigger pressure .have you got the sharpshooter 2. cheers lee

nice one mick,

thanks mike that's good info mt. what psi do you run it at mt.and does it stop and start if your working at height say gable end.

hy fellas my question is .Ive just purchased a sharpshooter 2 from the states for fine texture finishes over smooth finish render , I cannot find anything about the compressor size I need to run the gun on. went to machine mart and the arrogant t**t in there is trying to sell me a monster of a...

metal lathe fixed to panels .4x1 sand cement 2 lime scratch coat.4x1x1top coat.

Thanks for the info owls. I've maybe been miss informed I was told I can use sm700 as a base coat and finish all in one and can be sponge finished...ile be going on to sound brick work on an extension. what would you recommend primer for brick work. It will be hand applied .i want to use a all...

Isle be rendering a small extension in brick a.my question is what primer do I use for sm700 Thanks lads.

What primer do I need for sm700.....brick work .cheers lads.